Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Sliding glass doors
Impact garage doorsPGTCGI
Before
After
Before
After
Before
AfterWhy Royal Palm Beach Homeowners Choose Therma-Tru Windows & Doors
TruePane Windows & Doors provides independent Therma-Tru entry door repair, service, and full-frame replacement throughout Royal Palm Beach, Florida. We work on Classic-Craft and Smooth-Star fiberglass entry systems, Tru-Defense door units, and most Therma-Tru product lines installed in Palm Beach County homes. We are not an authorized Therma-Tru dealer or affiliate. What we are is a local glazing and door company that has spent years correcting Therma-Tru installation mistakes and Florida-specific failures across Royal Palm Beach, from binding slabs on west-facing exposures to threshold rot in older CBS ranch homes. Call (386) 251-6745 for a straight answer on whether your Therma-Tru door gets repaired or replaced.
Royal Palm Beach homeowners call us because a Therma-Tru door is an investment, and this climate tests that investment harder than most. The sun loads south-facing entries for hours each afternoon. Summer humidity saturates weatherstripping and swells wood subframes. And the same 2004 hurricane season that reshaped this village’s building codes also revealed which entry doors were never properly flashed or sealed. We see the failures. We fix them correctly, with the right parts and the right tolerances.
Why Trust TruePane Windows & Doors for Your Therma-Tru Windows & Doors?
Our techs have diagnosed and repaired hundreds of Therma-Tru entry systems in Royal Palm Beach and across Palm Beach County. We know the Classic-Craft fiberglass slab’s tendency to develop a slight afternoon warp on unshaded southern exposures. We know the Smooth-Star’s threshold profile and where the corner gaskets fail first. We know the Tru-Defense hinge fasteners and the screw-hole stripping pattern that shows up on doors that have been adjusted too many times.
Dale Kessler grew up off Crestwood Boulevard in Royal Palm Beach and has spent nearly three decades measuring, setting, and sealing windows and doors across Palm Beach County. He learned framing tolerances and Florida building code at Palm Beach State College, and he still references those lessons by habit. His father spent twenty years in general contracting, and the lesson that stuck was plain: a bad door installation costs twice what a good one does. That is why we measure every opening twice, shim to spec, and register warranty paperwork before we leave the driveway. Every Therma-Tru service call gets the same standard as a full installation. If the pane is not true, the job is not done.
Common Therma-Tru Windows & Doors Problems We Fix in Royal Palm Beach
- Afternoon door binding on Classic-Craft slabs. This is the single most common Therma-Tru complaint we hear in Royal Palm Beach. A Classic-Craft fiberglass entry door that swings fine at 9 a.m. starts sticking at the top corner by 2 p.m. The cause is thermal expansion of the fiberglass skin under direct sun load, compounded by original hinges that are undersized for the slab weight. The fix is not sanding the door. It is proper hinge replacement and re-shimming.
- Compressed and failed door-bottom weatherstripping. High-heat summers in Royal Palm Beach compress Therma-Tru door sweeps and corner gaskets faster than homeowners expect. Once the seal flattens against the threshold, you lose the air barrier and the door starts letting in dust, humidity, and noise. We replace with profile-matched Therma-Tru weatherstripping when available, or a heavy-duty aftermarket sweep that matches the original kerf.
- Stripped hinge screw holes. Therma-Tru doors are heavy. Over time, or after a few adjustment attempts, the original screws lose purchase in the wood subframe or the fiberglass jamb. The door sags, the latch misses the strike plate, and the problem compounds. We drill, dowel, and re-set the hinge fasteners with proper-length screws that reach the framing, not just the jamb skin.
- Fading and chalking on south-facing finishes. A Therma-Tru entry door on an unshaded south-facing wall in Royal Palm Beach takes relentless UV. The factory finish chalks, fades, or loses adhesion within a few years. We strip, prep, and refinish using coatings matched to Therma-Tru’s finish system, and we will tell you plainly if adding an overhang or awning is the smarter long-term move.
- Threshold and sub-sill rot from driven rain and humidity. Even with a decent overhang, Florida storms drive rain horizontally. If the original installer did not flash the rough sill correctly, water works its way under the threshold and into the wood buck. We pull the unit only when necessary, replace rotted sub-sill, flash the opening to current Palm Beach County code, and reset the door so water drains away instead of pooling.
Therma-Tru Parts & Our Repair-vs-Replace Approach
We stock Therma-Tru hinges, thresholds, and weatherstripping profiles locally for the most common Classic-Craft, Smooth-Star, and Tru-Defense door configurations in Royal Palm Beach. When a specific OEM part is on backorder or cost-prohibitive, we install heavy-duty aftermarket components that match the original profile and meet or exceed the load rating. We will always tell you which one you are getting and why.
Our honest assessment starts with the question: can this door be restored with adjustment, hardware, and weatherseal work rather than a full replacement? Most of the time, the answer is yes. Therma-Tru slabs are durable. The failures we see are usually in the hinges, thresholds, seals, or original installation, not the fiberglass or steel itself. When we do recommend replacement, it is because the slab has a structural issue or the homeowner wants an upgrade to impact-rated construction. If you are on the fence, call (386) 251-6745 and let us put eyes on it.
Our Therma-Tru Service Process - Step by Step
- 1
Diagnosis. We inspect the slab, hinges, threshold, weatherstripping, and rough opening. We measure the reveal gaps around the door in three positions per side. A door that is out of true tells us exactly where the problem lives. If the issue is thermal warp, we document it and explain the mechanical fix.
- 2
Repair or replacement plan, written down. We quote the work in writing, line by line. If it is a hinge replacement, we specify the hinge model and the fastener length. If it is a full-frame replacement in a Royal Palm Beach CBS home, we note the rough opening size and any HOA or permit requirements that apply to the job. No verbal handshakes.
- 3
Repair or install. We shim to spec, set fasteners into framing, and follow Therma-Tru’s installation tolerances. On impact-rated units, we follow the manufacturer’s fastening schedule and the county’s wind-borne debris region requirements. We do not cut corners on flashing or sealant. If it is not sealed right, the next storm will tell you.
- 4
Test and adjust. The door gets cycled a dozen times. We check the latch, the deadbolt throw, the sweep contact, and the reveal. The door should close with two fingers, latch without lifting, and seal evenly across the threshold. If it does not, we adjust until it does.
- 5
Warranty and paperwork. Before we leave, we register both warranty layers in writing per The Keystone Standard. You get the manufacturer warranty durations stated, our Done Right Promise, and a copy of everything in your hand. If it is not done right, we make it right. No arguing.
Therma-Tru Products We Service & Install in Royal Palm Beach
We service and install the Classic-Craft fiberglass entry system, the Smooth-Star fiberglass entry system, and the Tru-Defense entry system, along with compatible Therma-Tru thresholds, hinges, weatherstripping, and multipoint lock hardware. We regularly handle hurricane-proof front and entry doors, full frame replacement into CBS rough openings, and retrofit work where the original Therma-Tru slab stays and the hardware and sealing get rebuilt. We keep common threshold profiles and replacement sweeps on hand for Royal Palm Beach service calls, so most repairs happen in a single visit.
We Also Service These Brands
An entry door does not exist in a vacuum. The frame, the flashing, and the adjacent sidelites matter as much as the slab. TruePane Windows & Doors is an authorized installer for more than a dozen manufacturer lines, and we routinely service PGT, CGI, CWS, and ES Windows products alongside Therma-Tru work. If your Royal Palm Beach home has a mix of door brands and window brands, one service call covers it.
FAQs - Therma-Tru Windows & Doors Service in Royal Palm Beach
Why does my Therma-Tru fiberglass door bind or stick only in the afternoon?
Direct afternoon sun heats the fiberglass skin on your door, causing the slab to expand slightly and bind against the frame at the top corner. We see this regularly in Royal Palm Beach on west- and south-facing entries with no overhang protection. The fix is usually replacing the original hinges with heavier-duty continuous or multi-bearing hinges and re-shimming the unit so the door operates correctly through the full daily temperature range. Call (386) 251-6745 and we will diagnose it on site.
Can you replace the weatherstripping on my Therma-Tru entry door without replacing the whole door?
Yes. Weatherstripping is a wear part, and we replace door-bottom sweeps, corner gaskets, and jamb seals on Therma-Tru doors regularly without touching the slab. The key is matching the original kerf and profile so the new seal seats correctly. In Royal Palm Beach’s heat, compressed weatherstripping is one of the most common Therma-Tru repairs we perform.
How do you fix a Therma-Tru door that has a stripped hinge screw hole?
We remove the loose fastener, drill out the stripped hole, glue in a hardwood dowel, and re-set the hinge with a longer screw that reaches the structural framing behind the jamb. This restores the door’s load path and usually corrects the sag that caused the latch to miss the strike plate in the first place. It is a permanent fix when done properly.
Does a Therma-Tru Classic-Craft entry door need to be refinished often in Royal Palm Beach?
On a shaded or north-facing entry, a Classic-Craft finish can last many years with basic cleaning. On an unshaded south-facing wall in Royal Palm Beach, the UV load is severe, and we see finish chalking and fading within three to five years. We refinish using coatings compatible with Therma-Tru’s system, and we will tell you honestly if a protective overhang would extend the finish life more than another coat of paint.
Can you convert my standard Therma-Tru entry door to a hurricane-impact rated door without replacing the slab?
No. Impact rating comes from the slab construction, the glass package, and the anchoring system working together. You cannot retrofit impact resistance into a non-impact slab. We can replace the slab and frame with an impact-rated Therma-Tru compatible unit, or we can quote a PGT or CGI impact door if you want to compare options side by side. Call (386) 251-6745 for written numbers on both.
How much does Therma-Tru windows & doors service cost in Royal Palm Beach?
Therma-Tru service in Royal Palm Beach typically runs from about $180 for a basic weatherstripping and adjustment visit, up to $450 to $850 for hinge replacement with re-shimming and threshold work, depending on the door model and the condition of the rough opening. Full-frame impact-rated replacement starts higher and depends heavily on rough opening size, which in older Royal Palm Beach CBS homes is often non-standard. Call (386) 251-6745 for an exact quote on your door. Estimates are free.
Book Your Therma-Tru Service in Royal Palm Beach, FL
If your Therma-Tru door binds, leaks, sags, or just looks tired after ten Royal Palm Beach summers, call TruePane Windows & Doors at (386) 251-6745. A live person answers. We will schedule the visit, diagnose the problem, and put the fix in writing before any work begins.
Written by Dale Kessler, Owner at TruePane Windows & Doors, serving Royal Palm Beach and Palm Beach County since 2008.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.