CGI Glass Railing Systems Nationwide | TruePane Windows & Doors

CGI Glass Railing Systems: The Royal Palm Beach Owner’s Guide

If you’re searching this page, you likely have a CGI glass railing system with a cracked panel, a loose clamp, or a corroded bracket, and you want it matched to your exact model and priced honestly. We stock CGI-compatible glass railing components and complete panel assemblies for most CGI series, and typical installed replacement costs in Royal Palm Beach run $220 to $680 for a single panel swap with hardware, depending on glass thickness and post configuration. Most single-panel replacements are completed in one visit, and we keep common CGI clamp sets, standoffs, and tempered glass panels on the truck. You’ll know you’ve found the right page if your railing was installed as part of a CGI impact package, the etching says CGI or CGI Glass Railing, or your builder spec sheet lists CGI as the railing manufacturer.

Call (386) 251-6745

Which CGI Models This Applies To

CGI glass railing systems are not a one-size-fits-all product line. The company has produced several distinct railing series over the years, and the mounting hardware, glass thickness, and panel dimensions are not interchangeable between them. The most common CGI railing lines we service in Royal Palm Beach include the CGI Traditional, CGI Contemporary, and the newer CGI Solara series. You can identify your system by checking the small etched marking in the lower corner of a glass panel, or by measuring the glass thickness. CGI railing glass typically runs 3/8″ or 1/2″ thick, and some Solara models use 9/16″. If you can’t find the etching, measure the center-to-center spacing of your posts and the exact height of a panel, and we can usually identify the series from those numbers.

One compatibility gotcha we see regularly: older CGI Traditional series used a square-profile top clamp, while the Contemporary and Solara lines use a round taper clamp. They look similar at a glance, but the clamp bases are not cross-compatible. If you order the wrong clamp, you’ll have a gap under the glass or a bolt hole that doesn’t line up. We keep both styles in stock, and we verify the part against your existing hardware before we install anything. For CGI railing specifically, we recommend OEM hardware whenever it’s available. Aftermarket clamps can work, but the tolerances on CGI standoffs are tighter than most generic parts, and a mismatched clamp will eventually loosen under daily heat expansion cycles in South Florida. TruePane Windows & Doors is an independent service provider and not affiliated with CGI, but we source directly from authorized CGI distributors, so the parts we install are the same ones the manufacturer supplied originally.

Signs Your CGI Glass Railing Systems Is Failing

• Wobbling or rattling glass panels. The rubber gaskets inside the clamps compress over time, especially on west-facing installations in Royal Palm Beach where afternoon sun beats on the metal. Once a gasket flattens, the glass has play in the clamp and starts to rattle in the wind.
• White hazing or clouding at clamp points. This is electrolytic corrosion starting where the aluminum clamp meets stainless hardware in the presence of salt air. If you live east of Royal Palm Beach Boulevard or near the preserve, you’re more exposed to airborne salt than inland homes.
• Water staining running down from the bottom rail. CGI systems use weep holes in the base shoe to drain water. When sand and debris plug those holes, water sits against the glass edge and the silicone seal starts to degrade. The stain is the first visible warning.
• A chip or crack at the corner of a tempered panel. Tempered glass fails from edge contact. If a panel was installed slightly misaligned and the corner touches the post or the concrete, the point load will eventually cause a crack, usually within three to five years of installation.
• Loose or missing post caps and set screws. The set screws that hold post caps and top clamps in place back out under repeated thermal cycling. A missing set screw means the clamp is no longer carrying the glass load evenly.

Replacement Cost & What’s Included

A single tempered glass panel replacement for a CGI railing system in Royal Palm Beach typically runs $220 to $680 installed, depending on glass size, thickness, and whether the hardware is being replaced at the same time. A standard 36″ x 42″ 3/8″ panel with new gaskets and clamps lands in the $240 to $350 range. Larger panels, 1/2″ glass, or 9/16″ Solara panels will push toward the upper end. If the posts are damaged, add $85 to $160 per post for replacement and anchoring.

What’s included in our price: the glass panel, all gaskets and hardware, removal and disposal of the old panel, installation, and a written workmanship warranty. You’ll see the cost of the part and the labor separately on the quote, because you should know exactly what you’re paying for. No change orders, no surprise line items. We also register both warranty layers in writing before our truck leaves your driveway in Royal Palm Beach. If a measurement is wrong or a panel doesn’t fit, we make it right under our Done Right Promise, no paperwork fights.

DIY or Call Us?

You can safely inspect your CGI railing yourself. Check each clamp for loose set screws, look for missing gaskets, and note any panel that moves when you push gently on the glass. You can tighten a loose set screw with the correct Allen key if you know the size. That’s where we’d stop. Replacing a tempered glass panel means handling a 40-to-80-pound piece of glass that is under tension at the edges. One wrong angle against concrete and the entire panel shatters into hundreds of pieces. Removing and reinstalling clamps requires setting the glass at the correct reveal gap and torqueing hardware to CGI’s spec. Over-torqued clamps crack tempered glass. Under-torqued clamps drop panels. This is not a job where a YouTube video substitutes for the right tools and experience. We’ve been glazing in Palm Beach County for decades, and Dale Kessler has seen too many homeowners buy a panel, crack it during install, and pay twice. If a panel is cracked or a clamp is loose, call us at (386) 251-6745. We’ll match the part, install it correctly, and stand behind it.

FAQs